復卷機前后支承輥的速差,支承輥的速度差形成復卷力復卷力的大小決定了紙卷緊度的大小,提高復卷機復卷力可以增加紙卷的緊度第放卷的張力控制:在復卷一套紙卷期間應盡量避免改變復卷張力,以確保復卷紙機卷緊度內外均勻一致其次 在復卷過程中如果紙幅的張力控制太小紙卷將會產生松垮或在底輥上打滑,造成皺褶,紙頁交織等紙病而張力控制太大又會造成爆卷或損傷紙芯

　　衛生紙加工機械提高機器的效率需要做到壓紙輥的線壓力壓紙輥在復卷過程中給紙卷的加壓。在復卷的起步階段由壓紙輥提供紙卷額(e)外的載荷,和前后底輥一起作用給紙卷提供一個大的復卷力,隨著卷徑的增加壓紙輥的位置漸漸地在上升,壓紙輥所提供的載荷也漸漸地減小在一定程度上卷徑達到定值時,壓紙輥所提供的載荷將為零此時它僅作為維持紙卷位置的設備而存在,壓紙輥的壓力控制程序必須根據紙張質量和最終直徑進行選擇。